Exploitee.rs

MechDragon79 wrote:Well I glad to see people are getting through the setup and getting to play on the HC OS but for me still not getting pass the setup been doing and trying everything mention in this thread with not luck.

Did you go into recovery again, wipe, and then reinstall via the update.zip?

Try again see if it works.

Just updated. Everything went fine. Controller set up went fine. Philips AVR and Scientific Atlanta Cable Box from COX and Westinghouse TV . Downloaded update today. Put on 16gb Sandisk Cruzer that was freshly formatted 2x . put in USB slot next to Ethernet port. Live in Edmond OK. Hope this helps

just did a factory reset/clear cache and reinstalled.. still the same sign in issue.. Thank goodness im still within my 30 day return period and Frys's.. can we say "defective?"

gdeeble wrote: I had the same problem. I wasn't able to connect to mine when I first did it. I reset the router, and ironically that fixed it. What security are you running on it? Mine was WPA2 using TKIP+AES. Mine you this happened on both routers I have access to. Now I was able to connect to it using WPA, but the reset ultimately fixed it.

This actually worked! I'm not sure why it didn't work before as other devices were able to connect without issue, but since it's working now, thanks!

I've got some poor wifi signal strength issues and media playback issues now, but I'll work on them myself a bit. Thanks again!

joedeveloper wrote:

MechDragon79 wrote:Well I glad to see people are getting through the setup and getting to play on the HC OS but for me still not getting pass the setup been doing and trying everything mention in this thread with not luck.

Did you go into recovery again, wipe, and then reinstall via the update.zip?

Try again see if it works.

Still no luck.

jimbo2412 wrote:Just updated. Everything went fine. Controller set up went fine. Philips AVR and Scientific Atlanta Cable Box from COX and Westinghouse TV . Downloaded update today. Put on 16gb Sandisk Cruzer that was freshly formatted 2x . put in USB slot next to Ethernet port. Live in Edmond OK. Hope this helps

Hahaha, i live in Norman. Yay COX lol

long2know wrote:I installed Honeycomb and went through the set-up without a hitch.

I powered-off/unplugged the Revue a while later after the setup, and now when I turn it on, it seems to be stuck at the splash screen. Any ideas on what might cause this or a fix?

Similar issue here. HC was running like a champ on my Revue until a storm rolled through last night and knocked out the power for about 3 hours. Now all I see is the "Logitech Revue" splash when you first power on the unit. Tried to get into recovery mode, but it just reboots the box then stays on the same screen with both LEDs lit.

Has anybody tried to power-cycle their box yet?

joedeveloper wrote:

MechDragon79 wrote:Well I glad to see people are getting through the setup and getting to play on the HC OS but for me still not getting pass the setup been doing and trying everything mention in this thread with not luck.

Did you go into recovery again, wipe, and then reinstall via the update.zip?

Try again see if it works.

How can you go into recovery after applying the update? I have tried doing the same way by pressing FN key + the left arrow and it does not work. Did someone figure out a way to go into recovery on HC???

cesarb wrote:How can you go into recovery after applying the update? I have tried doing the same way by pressing FN key + the left arrow and it does not work. Did someone figure out a way to go into recovery on HC???

Try ALT+L. This seems to have worked for other people.

jeffrapp wrote:

cesarb wrote:How can you go into recovery after applying the update? I have tried doing the same way by pressing FN key + the left arrow and it does not work. Did someone figure out a way to go into recovery on HC???

Try ALT+L. This seems to have worked for other people.

Ok i was able to re flash but im having the same issue as before. Username and password do not match....